Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
The publisher is making several great pointers on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in the content which follows.
Installing a tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult project. If the old tub is easily obtainable, the job can relocate speedily; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will need an assistant to move out the old bathtub as well as embeded in the brand-new one. Ensure you have qualified yourself for the task as well as fit attempting it. Instead of employing a specialist to take over a halfway-completed job, it is far better to think about employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This short article will help you install a brand-new bathtub in your bathroom if you have actually already bought a brand-new tub and also don't require to change the plan of your previous water system pipelines.
Your devices and also material checklist must consist of the following:
Preparing for the Installation
To start with, the supporting frame supplied with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets device to avoid pressure on the tub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is disconnect the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the restricted gain access to that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the faucets have been removed, the holes in the bath/basin will need to be cleansed of any old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Making use of both wood boards under its feet, place the bath tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto four little factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leakages as well as tighten them if required. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub ought to wait until the tub has been utilized at the very least when as this will resolve it right into its final position.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in location in between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former kind needs to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split an inflexible seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and cartridges, as well as are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily offered on the market. It is a good idea to fit the floor tiles using waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent person who reads on Installing A Bathtub, I figured sharing that excerpt was essential. Sharing is caring. Helping people is fun. Bless you for your time. Visit again soon.
Trusted plumbing solutions at hand. Report this page